Focused arrival windows
Useful updates and clear arrival timing.
Standing seam and corrugated panels installed right the first time
Metal Roofing in Huntsville built for Texas storms and heat
Metal Roofing in Huntsville is the long-term answer for homeowners tired of replacing hail-battered shingles every few years. We install standing seam and corrugated metal roof systems across Walker County that shrug off 60 mph wind gusts, shed pine needles, and reflect summer heat instead of soaking it up. If your current roof is 15 years old or you just got a storm damage claim denied, call us for a straight answer.
Prepared local crewClear options firstFinal testing and walkthrough
Clear scope before work
Review the approach and price before deciding.
Prepared, clean crews
Equipped vehicles and respectful cleanup.
Local accountability
Neighbors serving neighbors with follow-through.
What is included
What our Metal Roofing service includes
Every metal roof installation includes the full tear-off, new underlayment, new flashing, and the panel system itself. Add-ons like gutter replacement, skylight installation, or attic ventilation upgrades are quoted separately so you can see exactly what you are paying for.
Full tear-off and disposal
We remove the old shingles or panels, haul them off in our dump trailer, and sweep the yard with a magnetic sweeper. You do not need to rent a dumpster or coordinate disposal. The tear-off is included in every quote.
New underlayment and ice shield
Synthetic underlayment covers the entire deck, with ice and water shield doubled in valleys and along the eaves. This is the waterproofing layer that protects you if a panel ever gets damaged. We never skip it to save a few dollars.
Panel system and fasteners
Your choice of standing seam or corrugated panels in the color and profile you pick. All fasteners are color-matched with rubber washers, and standing seam panels get mechanically seamed at every rib. This is the roof itself, done to manufacturer spec.
Flashing and trim
New drip edge, valley flashing, pipe boots, and ridge caps. Every penetration gets sealed properly. Flashing failure is the number one cause of metal roof leaks, so we treat this step as seriously as the panels.
Workmanship warranty
You get a written workmanship warranty on top of the manufacturer's panel warranty. If anything we installed fails because of how we installed it, we come back and fix it. That is the difference between a real roofer and a guy with a truck.
PLAN
Request a service estimate
Share what is happening and receive a clear next step from the local team.
Service overview
What Metal Roofing in Huntsville actually involves
Metal Roofing in Huntsville is a roof system built from steel or aluminum panels locked together over a weather-tight underlayment, replacing asphalt shingles with a surface that lasts 40 to 70 years. We start by stripping the old roof down to the deck, checking for soft spots and rot, then laying ice and water shield along the eaves and valleys. Panels get fastened with screws that have rubber washers, and every penetration gets sealed with roof flashing. The whole job usually takes three to five days on a standard 2,000 square foot ranch home.
Huntsville sits in a pocket of East Texas where summer attic temperatures push past 140 degrees and spring hail rolls through Walker County almost every year. Asphalt shingles dry out and crack under that cycle. A metal roof Huntsville homeowners install once tends to outlive the mortgage. We also see a lot of older homes near Sam Houston State with sagging decking from decades of clogged gutters, so we check the structure before we ever quote panels. Call 766837673 and we will walk your roof with you.
- Stands up to hail — Class 4 impact-rated panels take hail that would total an asphalt roof. After the last big Walker County hailstorm, we replaced shingles on three neighbors and none of the metal roofs on the same street needed anything but a rinse. That is the difference you are paying for.
- Cuts summer cooling costs — A reflective metal roof can drop attic temperatures by 20 to 30 degrees compared to dark shingles. Huntsville summers run hot enough that homeowners regularly tell us their AC runs less the first July after installation. Lower attic heat also extends the life of your HVAC equipment.
- Sheds debris and rain — Pine needles, leaves, and heavy rain slide right off a smooth standing seam panel. That means fewer clogged gutters, less ponding water at the eaves, and no more shingle granules washing into your flower beds. If you are tired of climbing a ladder every fall, this is the fix.
- Lasts decades, not years — A quality standing seam metal roof installed in Huntsville TX today should still be watertight when your kids inherit the house. Most asphalt roofs in this climate are done in 12 to 18 years. When you price metal roof cost Huntsville TX homeowners pay, divide it by 50 years and the number gets a lot friendlier.
- We measure twice — Panel lengths are cut to the inch based on actual field measurements, not a satellite estimate. That means fewer seams, less waste, and a cleaner roofline. On a recent Crabbs Prairie job we cut waste to under 4 percent, which saved the homeowner real money on material.
- Storm-season scheduling — After a hail event in Walker County, we prioritize active leaks and tarp-overs first, then schedule full metal roof replacements in the order calls came in. You get a real date, not a vague window. We text you the day before with the crew lead's name.
- Metal roofer Huntsville homeowners call back — Most of our metal roof work comes from repeat customers and their neighbors. When you do a roof right, people notice. We have re-roofed entire streets in Harmony and Pine Hill because one homeowner told the next one who did the work.
- Honest answers on repair vs replace — Sometimes a metal roof repair in Huntsville Texas is all you need, and we will tell you that even when a full replacement would pay us more. If your panels are sound and the leak is a flashing failure, we fix the flashing and send you on your way.
The service timeline
How our metal roof installation works
Free roof inspection
We get on the roof, measure the square footage, check the decking from the attic side, and photograph every problem area. You get a written scope with panel options, colors, and a firm price. Most inspections take 45 minutes to an hour.
Tear-off and deck repair
We strip the old shingles down to bare wood, haul everything off in a dump trailer, and replace any rotten decking we find. We run a magnetic sweeper across the yard twice before we leave for the day so your driveway and grass stay nail-free.
Underlayment and flashing
Synthetic underlayment goes down over the whole deck, with ice and water shield doubled up in valleys and along the eaves. New drip edge and roof flashing go on before a single panel is set. This is the layer that keeps you dry for the next 40 years.
Panel installation
Panels are cut on-site with a shingle cutter set up in the driveway, then carried up and fastened with color-matched screws. Standing seam panels get mechanically seamed at every rib. A typical 2,000 square foot roof takes two to three days for the panel work alone.
Final walkthrough and cleanup
We walk the roof with you, show you the ridge vent, the flashing details, and the panel seams, then run the magnetic sweeper one last time. You get a workmanship warranty in writing and our direct line for anything that comes up later.
Tools and methods01 02 03 04 05 06 07 08 09 10
Tools and methods we use
Standing seam seamer
Mechanically locks the panel ribs together for a watertight seam. Hand-seaming is slower but produces a tighter, more reliable lock than a powered seamer on short runs.
Roofing nail gun
Fastens underlayment and decking quickly and consistently. We set the depth so nails sit flush without tearing through the felt.
Magnetic sweeper
Picks up stray screws and nails from your lawn and driveway. We run it at the end of every workday, not just at the end of the job.
Safety harness and roofing ladder
OSHA-compliant fall protection on every roof, every time. Steep pitches and two-story homes get anchored harness systems, no exceptions.
Chalk line and utility knife
Layout and precise cuts on panels and underlayment. Clean cuts mean tight seams and fewer leak points down the road.
Pry bar and roofing hammer
Tear-off and detail work. The pry bar gets under stubborn shingles and flashing without damaging the deck; the hammer sets nails in tight spots a gun cannot reach.
Manufacturer-spec installation
We follow the panel manufacturer's installation manual to the letter, including fastener spacing, seam type, and underlayment requirements. This is what keeps your warranty valid. Cut corners here and the manufacturer can deny a claim later.
Ice and water shield in critical zones
Valleys, eaves, and around every penetration get a double layer of ice and water shield. This is the last line of defense if a panel or flashing ever fails. It costs a little more and it is worth every dollar.
Attic ventilation check
Before we install a metal roof, we measure intake and exhaust ventilation in the attic. Undersized ventilation causes condensation, which rots the deck from underneath. We fix it before the panels go on, not after.
Photo documentation
We photograph the deck, the underlayment, the flashing, and the finished roof. You get the photos, and they are invaluable if you ever file an insurance claim or sell the house.
Where this service helps
When Huntsville homeowners choose metal
Your asphalt shingles are 15 years old and you just got another insurance claim denied after hail.
We inspect the roof, document the actual condition, and quote a metal roof replacement that will not need to be claimed again. Standing seam panels are Class 4 impact rated, which many insurers recognize with a premium discount. You stop the cycle of replace-claim-replace and get a roof that outlasts the mortgage. Most homeowners see a premium reduction once the metal roof is on file.
You are building a new house in Pine Prairie and want to pick the roof before the framing is done.
We work with your builder to spec the panel system, order materials, and schedule installation right after the decking goes on. Standing seam or corrugated, your choice of color and profile. The roof is installed before the interior finishes go in, so there is no disruption later. You get a 40-year panel warranty from day one.
Your metal roof is leaking around the chimney and you are not sure if it needs repair or replacement.
We get on the roof, find the actual source, and give you both numbers. If the panels are sound and the leak is flashing, we repair it. If the deck is rotted or the panels are failing, we quote replacement. You get an honest answer and a fixed roof. Most of these calls end with a flashing repair in the hundreds, not a replacement in the thousands.
You own a commercial building in Huntsville with a flat roof that ponds water every time it rains.
We inspect the drainage, check the membrane, and recommend either a TPO retrofit or a roof coating depending on the condition. If the membrane is sound, a coating buys you years at a fraction of replacement cost. Ponding water is eliminated, the membrane is protected, and you avoid a full replacement for now. We will tell you honestly when replacement is the better call.
Local execution
How Metal Roofing works in Huntsville
Huntsville sits in East Texas where the roof takes a beating from three directions: summer heat that bakes shingles, spring hail that rolls through Walker County, and winter wind that finds every loose fastener. Metal handles all three better than anything else. The other local factor is the tree canopy. Pine needles and leaves pile up on roofs here, and on a shingle roof that means rot at the eaves. On a smooth metal panel they slide off. We also deal with older housing stock near Sam Houston State, where decking is often soft from decades of clogged gutters. Before we quote a metal roof installation Huntsville TX homeowners can trust, we check the deck from the attic side. If you want to know how much for metal roof in Huntsville, the honest answer depends on what we find up there.
Pine Hill
Heavy pine canopy means debris loads on roofs. Metal panels shed needles better than shingles, which cuts down on eave rot and clogged gutters.
Crabbs Prairie
Open lots and fewer trees mean full sun and more hail exposure. Class 4 impact panels are a smart upgrade out here.
Harmony
Mix of older homes and new construction. We see a lot of soft decking on the older houses from years of gutter overflow.
Pine Prairie
Newer development with active building. We work with builders to spec metal roofing before the interior finishes go in.
Dodge
Rural properties with outbuildings and shops. Corrugated metal is a popular, affordable choice for barns and workshops.
Summer attic temperatures above 140 degrees
Asphalt shingles dry out and crack. Metal reflects the heat and keeps the attic 20 to 30 degrees cooler, which extends HVAC life and cuts cooling bills.
Annual spring hail in Walker County
Hail bruises shingles and dents metal. Class 4 impact-rated panels resist the impact that totals an asphalt roof, which is why so many homeowners upgrade after a claim.
Heavy pine and leaf debris
Debris traps moisture against shingles and rots the deck. Smooth metal panels shed it, so gutters stay clear and the roof dries fast after rain.
High wind from winter fronts
Loose fasteners let panels lift. We install to manufacturer wind ratings and check every screw, which is why our metal roofs stay put when others peel.
Before and after
What a successful service visit changes.
Hail-totaled shingles to standing seam
Before
A 2,200 square foot home in Crabbs Prairie had asphalt shingles totaled by hail. The insurance adjuster approved a shingle replacement, but the homeowner wanted to upgrade. The deck had two soft spots near the valleys that needed replacement.
After
We installed standing seam metal in a charcoal finish over new synthetic underlayment and ice shield. The upgrade cost the homeowner about $6,000 out of pocket after the insurance payout. The roof is now Class 4 impact rated and the insurer applied a premium discount.
Maintenance: Rinse the panels once a year and check the fasteners after any major storm. That is it. No granules, no cracking, no re-shingling every 15 years.
Leaking chimney flashing repaired
Before
A homeowner in Harmony had a ceiling stain that kept coming back after every rain. Two previous roofers had patched the shingles around the chimney without fixing the actual flashing. The deck underneath was wet and starting to soften.
After
We removed the old flashing, replaced the rotted deck section, and installed new counter-flashing with proper sealant. Total repair was $850. The ceiling stain has not returned in two years, and the deck is dry.
Maintenance: Check the chimney flashing every fall before the rainy season. A five-minute visual inspection catches most problems before they leak.
Corrugated shop roof replaced
Before
A 1,800 square foot shop in Dodge had corrugated metal panels that were rusted through in several spots. The fasteners had backed out and the panels lifted in wind. Rain was getting in and ruining stored equipment.
After
We tore off the old panels, replaced three sheets of decking, and installed new corrugated metal with oversized gasketed fasteners. The job took two days and cost $9,400. The shop is dry and the panels are rated for 140 mph winds.
Maintenance: Walk the roof twice a year and tighten any loose fasteners. On a corrugated roof this is the single most important maintenance task.
Problems we solve
Metal roof problems we fix in Huntsville
Metal roofs fail in predictable ways. Fasteners back out, flashing pulls loose, and condensation rots the deck from underneath. We see the same handful of issues over and over in Walker County, and we know how to fix each one without selling you a whole new roof.
Loose or backing-out fasteners
Panels lift in high wind, water gets under the seams, and the next storm peels a section off. A few missing screws today becomes a full panel replacement after the next blue norther. We inspect every fastener, replace the failed ones with oversized screws, and reseal the washers. On older corrugated roofs we often add a new gasket washer to every screw. This is a half-day job that adds years to the roof.
Flashing failure around chimneys and vents
Water runs straight down the chimney into your attic and shows up as a ceiling stain weeks later. By then the insulation and drywall are already wet and growing mold. We pull the old flashing, check the deck underneath for rot, and install new flashing with proper counter-flashing and sealant. We also check every pipe boot and ridge cap while we are up there. Most flashing repairs run a few hundred dollars.
Condensation rotting the deck
Metal roofs sweat when attic ventilation is poor. The moisture drips onto the decking, rots the wood, and eventually the panels have nothing solid to hold onto. This is the most expensive metal roof problem to fix. We check attic ventilation on every metal roof inspection. If intake and exhaust are undersized, we add ridge vent or soffit vents to get air moving. Fixing ventilation now prevents a full deck replacement later.
Storm damage and hail dents
Cosmetic dents are ugly but usually not a leak risk. The real damage is to the fasteners and flashing, which take the impact and fail first. Ignoring it means a leak shows up the next time it rains hard. We document all storm damage with photos for your insurance claim, then repair the fasteners, flashing, and any panels that actually need replacing. We do not push a full replacement when a targeted repair will do the job.
Proof behind the promise
Licensed, insured, and certified
Technical expertise
26 years roofing Huntsville homes
Pro Roofing Huntsville has been on roofs in Walker County since 2000. That is 26 years of Texas heat, hail, and humidity teaching us what fails and what holds. We are a NRCA member and carry manufacturer certifications that let us offer extended warranties on the panels and the labor. Our crews are OSHA safety certified and fully insured with workers compensation coverage. We have installed metal roofing on everything from 1940s bungalows near the university to new construction in Pine Prairie.
- NRCA member with 26 years of continuous local roofing experience
- Manufacturer-certified installer for standing seam metal panel systems
- OSHA safety certified crews, fully insured with workers compensation
- Thousands of Huntsville-area roofs inspected, repaired, and replaced
- Direct experience with Walker County hail, wind, and heat damage patterns
Customer stories
What Huntsville homeowners say
Dana R.Homeowner, Pine Hill TX
We got three quotes for a metal roof and Pro Roofing was the only one that actually got on the roof and measured. The others used satellite pictures. They found soft decking near the chimney that would have been a leak in a year. Install took four days, crew cleaned up every nail, and the house is noticeably cooler this summer.
Marcus T.Homeowner, Crabbs Prairie TX
Hail totaled our shingles in 2024. We decided to upgrade to standing seam instead of putting shingles back on. Pro Roofing worked with our adjuster, documented everything, and the claim covered most of the metal upgrade. Two years in and the roof still looks brand new. Worth every penny.
Elaine W.Homeowner, Harmony TX
We had a leak around the skylight and thought the whole roof was done. They came out, found the flashing had failed, and repaired it for a few hundred dollars instead of selling us a replacement. Honest people. We called them back the next year to do gutters and a full metal roof on the shop.
How much does a metal roof cost in Huntsville TX?
Most residential metal roof installations in Huntsville run $12,000 to $28,000 in 2026, depending on square footage, panel type, and how much decking needs replacing. Standing seam costs more than corrugated. A simple 1,500 square foot ranch with good decking sits at the low end. Two-story homes with steep pitches and multiple valleys land higher. We give you a firm number after the inspection, not a range.
Who installs metal roofs near me in Huntsville Texas?
Pro Roofing Huntsville installs metal roofing across Walker County and the surrounding towns, including Pine Hill, Crabbs Prairie, Harmony, and Dodge. We are a licensed Texas roofing contractor, NRCA member, and manufacturer-certified for standing seam systems. Call 766837673 and we will schedule a free inspection. We serve ZIP codes 77340, 77341, 77342, 77343, and 77344.
How long does a metal roof last in Huntsville TX?
A quality standing seam metal roof installed here lasts 40 to 70 years. The panels themselves often carry a 40-year manufacturer finish warranty. What kills metal roofs early is bad installation, not the metal. Poorly fastened panels back out in high wind, and skipped underlayment lets condensation rot the deck. Do it right once and you will not think about your roof again.
Are metal roofs good for Huntsville TX weather?
Yes. Metal handles the three things that destroy roofs here: hail, wind, and heat. Class 4 impact panels resist hail that totals asphalt shingles. Standing seam panels are rated for winds over 140 mph when installed to spec. And the reflective finish keeps attic temperatures 20 to 30 degrees cooler in July and August. It is the best roof system for this climate.
Frequently asked questions
Frequently Asked Questions
Not seeing your question? Our local team can help you understand urgency, scheduling and what to expect.
Ask the local teamRelated services
Related Services
Roof Installation
New construction and full re-roofs across Huntsville. We install metal, shingle, and tile systems from the deck up, with proper underlayment and flashing every time. If you are building in Pine Prairie or replacing a worn-out roof, this is where we start.
View serviceRoof Replacement
When repairs stop making sense, we tear off the old roof and install new. Most Huntsville homeowners upgrading to metal come through this service. We handle the dumpster, the tear-off, any decking repair, and the full installation in one project.
View service
Roof Repair
Leaks, missing panels, failed flashing, and storm damage. We fix metal roofs and shingle roofs alike. If a tree limb punched through a panel in Crabbs Prairie, we can often match and replace the section without redoing the whole roof.
View service
Roof Inspection
A 45-minute inspection with photos and a written report. We check the deck, the underlayment, the flashing, and the fasteners. Great before you buy a house or file an insurance claim after a Walker County hailstorm.
View serviceContact the local team
Contact Pro Roofing Huntsville
Call us any time, day or night. Our office answers from 8 a.m. to 6 p.m. Monday through Friday, and the emergency line stays open around the clock for active leaks and storm damage. Most Huntsville inspections get scheduled within 48 hours, and emergency calls get a same-day tarp.